Version 1 (modified by amain, 3 years ago) (diff)

--

NFS (Jessie with systemd)

Looking for valid bootloader image....
Jumping to start of image at address 0xbfc80000


U-Boot 1.1.1 (UBNT Build ID: 4670715-gbd7e2d7) (Build time: May 27 2014 - 11:16:22)

BIST check passed.
UBNT_E100 r1:2, r2:18, f:4/71, serial #: 44D9E7401483
MPR 13-00318-18
Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM:  512 MB
Clearing DRAM....... done
Flash:  4 MB
Net:   octeth0, octeth1, octeth2

USB:   (port 0) scanning bus for devices... 1 USB Devices found
       scanning bus for storage devices...
  Device 0: Vendor:          Prod.: USB DISK 2.0     Rev: PMAP
            Type: Removable Hard Disk
            Capacity: 3824.0 MB = 3.7 GB (7831552 x 512)
 0 
Octeon ubnt_e100# run nfs
Interface 0 has 3 ports (RGMII)
Using octeth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'vmlinux.64'.
Load address: 0x9f00000
Loading: octeth0: Up 1000 Mbps Full duplex (port  0)
#########################################
done
Bytes transferred = 5762952 (57ef88 hex), 10519 Kbytes/sec
argv[2]: coremask=0x3
argv[3]: endbootargs
ELF file is 64 bit
Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x15d0a18
Allocated memory for ELF segment: addr: 0xffffffff81100000, size 0x15d0a18
Processing PHDR 0
  Loading 57da00 bytes at ffffffff81100000
  Clearing 1053018 bytes at ffffffff8167da00
## Loading Linux kernel with entry point: 0xffffffff81107210 ...
Bootloader: Done loading app on coremask: 0x3
[    0.000000] Linux version 3.18.21 (amain@dev) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r47045) ) #33
 SMP Sun Oct 4 16:49:25 CEST 2015
[    0.000000] CVMSEG size: 2 cache lines (256 bytes)
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 000d0601 (Cavium Octeon+)
[    0.000000] Checking for the multiply/shift bug... no.
[    0.000000] Checking for the daddiu bug... no.
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 0000000005800000 @ 0000000002700000 (usable)
[    0.000000]  memory: 0000000007c00000 @ 0000000008200000 (usable)
[    0.000000]  memory: 000000000fc00000 @ 0000000410000000 (usable)
[    0.000000]  memory: 00000000015d0a18 @ 0000000001100000 (usable)
[    0.000000] Wasting 243712 bytes for tracking 4352 unused pages
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Using internal Device Tree.
[    0.000000] software IO TLB [mem 0x0368e000-0x0768e000] (64MB) mapped at [800000000368e000-800000000768dfff]
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x01100000-0xefffffff]
[    0.000000]   Normal   [mem 0xf0000000-0x41fbfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x01100000-0x026cffff]
[    0.000000]   node   0: [mem 0x02700000-0x07efffff]
[    0.000000]   node   0: [mem 0x08200000-0x0fdfffff]
[    0.000000]   node   0: [mem 0x410000000-0x41fbfffff]
[    0.000000] Initmem setup node 0 [mem 0x01100000-0x41fbfffff]
[    0.000000] Primary instruction cache 32kB, virtually tagged, 4 way, 64 sets, linesize 128 bytes.
[    0.000000] Primary data cache 16kB, 64-way, 2 sets, linesize 128 bytes.
[    0.000000] PERCPU: Embedded 12 pages/cpu @8000000007749000 s10752 r8192 d30208 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 122667
[    0.000000] Kernel command line:  root=/dev/nfs ip=dhcp rw mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),
64k@1024k(eeprom) console=ttyS0,115200
[    0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000] Memory: 400752K/497472K available (4100K kernel code, 292K rwdata, 972K rodata, 240K init, 16706K 
bss, 96720K reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  CONFIG_RCU_FANOUT set to non-default value of 32
[    0.000000]  RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:127
[    0.629849] Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=2000000)
[    0.637942] pid_max: default: 32768 minimum: 301
[    0.642801] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
[    0.649279] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)
[    0.657338] Checking for the daddi bug... no.
[    0.664290] SMP: Booting CPU01 (CoreId  1)...
[    0.668658] CPU1 revision is: 000d0601 (Cavium Octeon+)
[    0.668831] Brought up 2 CPUs
[    0.677820] devtmpfs: initialized
[    0.686534] NET: Registered protocol family 16
[    0.691814] Not in host mode, PCI Controller not initialized
[    0.715665] SCSI subsystem initialized
[    0.719718] usbcore: registered new interface driver usbfs
[    0.725176] usbcore: registered new interface driver hub
[    0.730465] usbcore: registered new device driver usb
[    0.736595] Switched to clocksource OCTEON_CVMCOUNT
[    0.743904] NET: Registered protocol family 2
[    0.749257] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.756284] TCP bind hash table entries: 4096 (order: 5, 131072 bytes)
[    0.762835] TCP: Hash tables configured (established 4096 bind 4096)
[    0.769143] TCP: reno registered
[    0.772243] UDP hash table entries: 256 (order: 2, 24576 bytes)
[    0.778197] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes)
[    0.784926] NET: Registered protocol family 1
[    0.789667] RPC: Registered named UNIX socket transport module.
[    0.795442] RPC: Registered udp transport module.
[    0.800127] RPC: Registered tcp transport module.
[    0.804807] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.816182] futex hash table entries: 512 (order: 4, 65536 bytes)
[    0.824857] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.831294] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.841491] msgmni has been set to 782
[    0.846807] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.854110] io scheduler noop registered
[    0.857967] io scheduler deadline registered (default)
[    0.863290] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO driver probed.
[    0.871146] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.878670] console [ttyS0] disabled
[    0.882168] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 41, base_baud = 31250000) is a OCTEON
[    0.891937] console [ttyS0] enabled
[    0.891937] console [ttyS0] enabled
[    0.898849] bootconsole [early0] disabled
[    0.898849] bootconsole [early0] disabled
[    0.907533] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 42, base_baud = 31250000) is a OCTEON
[    0.918232] octeon_rng octeon_rng: Octeon Random Number Generator
[    0.929818] loop: module loaded
[    0.933944] of-flash 1f400000.nor: Can't get bank width from device tree
[    0.941050] libphy: mdio-octeon: probed
[    0.946945] mdio-octeon 1180000001800.mdio: Version 1.0
[    0.952869] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.959574] ehci-pci: EHCI PCI platform driver
[    0.964172] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.970524] uhci_hcd: USB Universal Host Controller Interface driver
[    0.977184] usbcore: registered new interface driver usb-storage
[    0.983253] octeon_wdt: Initial granularity 5 Sec
[    0.988737] cavium-ethernet 1.9
[    0.994785] Interface 0 has 3 ports (RGMII)
[    1.012987] OcteonUSB 16f0010000000.usbc: Octeon Host Controller
[    1.019351] OcteonUSB 16f0010000000.usbc: new USB bus registered, assigned bus number 1
[    1.027459] OcteonUSB 16f0010000000.usbc: irq 124, io mem 0x00000000
[    1.034099] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.040951] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.048206] usb usb1: Product: Octeon Host Controller
[    1.053284] usb usb1: Manufacturer: Linux 3.18.21 Octeon USB
[    1.058964] usb usb1: SerialNumber: 16f0010000000.usbc
[    1.065016] hub 1-0:1.0: USB hub found
[    1.068894] hub 1-0:1.0: 1 port detected
[    1.073284] OcteonUSB 16f0010000000.usbc: Registered HCD for port 0 on irq 124
[    1.080972] TCP: cubic registered
[    1.084310] NET: Registered protocol family 17
[    1.088908] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load 
br_netfilter if you need this.
[    1.101598] Bridge firewalling registered
[    1.105649] 8021q: 802.1Q VLAN Support v1.8
[    1.109999] Bootbus flash: Setting flash for 4MB flash at 0x1f800000
[    1.116433] phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00
00a7
[    1.126811] Amd/Fujitsu Extended Query Table at 0x0040
[    1.131984]   Amd/Fujitsu Extended Query version 1.1.
[    1.137058] phys_mapped_flash: Swapping erase regions for top-boot CFI table.
[    1.144209] number of CFI chips: 1
[    1.147652] 3 cmdlinepart partitions found on MTD device phys_mapped_flash
[    1.154546] Creating 3 MTD partitions on "phys_mapped_flash":
[    1.160314] 0x000000000000-0x000000080000 : "boot0"
[    1.166537] 0x000000080000-0x000000100000 : "boot1"
[    1.172754] 0x000000100000-0x000000110000 : "eeprom"
[    1.180197] console [netcon0] enabled
[    1.183889] netconsole: network logging started
[    1.189056] eth0: 1000 Mbps Full duplex, port 0
[    1.208603] Sending DHCP requests ., OK
[    1.244599] IP-Config: Got DHCP answer from 192.168.1.100, my address is 192.168.1.2
[    1.253160] IP-Config: Complete:
[    1.256416]      device=eth0, hwaddr=44:d9:e7:40:14:83, ipaddr=192.168.1.2, mask=255.255.255.0, gw=192.168.1.1
00
[    1.266630]      host=192.168.1.2, domain=thuis.lan, nis-domain=(none)
[    1.273202]      bootserver=192.168.1.100, rootserver=192.168.1.100, rootpath=/nfs/root
[    1.281045]      nameserver0=10.0.2.10
[    1.328269] VFS: Mounted root (nfs filesystem) on device 0:11.
[    1.334404] Freeing unused kernel memory: 240K (ffffffff81644000 - ffffffff81680000)
[    1.432767] usb 1-1: new high-speed USB device number 2 using OcteonUSB
[    1.621753] usb 1-1: New USB device found, idVendor=13fe, idProduct=4100
[    1.628505] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.635692] usb 1-1: Product: USB DISK 2.0
[    1.639825] usb 1-1: Manufacturer:         
[    1.644034] usb 1-1: SerialNumber: 070853D622560805
[    1.650137] usb-storage 1-1:1.0: USB Mass Storage device detected
[    1.657702] scsi host0: usb-storage 1-1:1.0
[    1.674350] random: systemd urandom read with 24 bits of entropy available

Welcome to Debian GNU/Linux 8 (jessie)!

[    1.778033] NET: Registered protocol family 10
[    2.076159] systemd-sysv-generator[56]: Overwriting existing symlink /run/systemd/generator.late/rcS.service w
ith real service
         Expecting device dev-ttyS0.device...
[  OK  ] Reached target Remote File Systems (Pre).
[  OK  ] Reached target Paths.
[  OK  ] Reached target Encrypted Volumes.
         Expecting device dev-sda1.device...
[  OK  ] Created slice Root Slice.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Listening on Delayed Shutdown Socket.
[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Listening on udev Control Socket.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Listening on Journal Socket.
[  OK  ] Created slice System Slice.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
         Starting Increase datagram queue length...
         Starting Create list of required static device nodes...rrent kernel...
         Starting udev Coldplug all Devices...
         Mounting POSIX Message Queue File System...
         Starting Load Kernel Modules...
[  OK  ] Reached target Slices.
         Starting Remount Root and Kernel File Systems...
[  OK  ] Started Increase datagram queue length.
[    2.672426] scsi 0:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 6
[    2.683276] sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
[    2.693125] sd 0:0:0:0: [sda] Write Protect is off
[    2.699061] sd 0:0:0:0: [sda] No Caching mode page found
[    2.704467] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    2.731955]  sda: sda1 sda2
[  OK  ] Started Create list of required static device nodes ...current[    2.743722] sd 0:0:0:0: [sda] Attached 
SCSI removable disk
 kernel.
[  OK  ] Mounted POSIX Message Queue File System.
[FAILED] Failed to start Load Kernel Modules.
See 'systemctl status systemd-modules-load.service' for details.
[FAILED] Failed to start Remount Root and Kernel File Systems.
See 'systemctl status systemd-remount-fs.service' for details.
[  OK  ] Started udev Coldplug all Devices.
         Activating swap /swap...
         Starting Load/Save Random Seed...
         Starting Apply Kernel Variables...
         Starting Create Static Device Nodes in /dev...
[  OK  ] Listening on Syslog Socket.
[    3.034703] swapon: swapfile has holes
[  OK  ] Reached target Sockets.
         Starting Journal Service...
[  OK  ] Started Journal Service.
[FAILED] Failed to activate swap /swap.
See 'systemctl status swap.swap' for details.
[DEPEND] Dependency failed for Swap.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] [    3.319938] systemd-udevd[87]: starting version 215
Started udev Kernel Device Manager.
         Starting Copy rules generated while the root was ro...
         Starting LSB: Tune IDE hard disks...
[  OK  ] Started Copy rules generated while the root was ro.
[  OK  ] Started LSB: Tune IDE hard disks.
[    3.667397] random: nonblocking pool is initialized
[  OK  ] Found device USB_DISK_2.0 1.
[  OK  ] Found device /dev/ttyS0.
         Mounting /boot...
[    4.360463] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  OK  ] Mounted /boot.
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Directories...
         Starting LSB: Raise network interfaces....
         Starting LSB: ebtables ruleset management...
[  OK  ] Reached target Remote File Systems.
         Starting Trigger Flushing of Journal to Persistent Storage...
[    4.649438] systemd-journald[83]: Received request to flush runtime journal from PID 1
[  OK  ] Started Trigger Flushing of Journal to Persistent Storage.
[  OK  ] Started LSB: ebtables ruleset management.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started LSB: Raise network interfaces..
[  OK  ] Reached target Network.
[  OK  ] Reached target Network is Online.
[  OK  ] Reached target System Initialization.
[  OK  ] Reached target Timers.
[  OK  ] Reached target Basic System.
         Starting Regular background program processing daemon...
[  OK  ] Started Regular background program processing daemon.
         Starting OpenBSD Secure Shell server...
[  OK  ] Started OpenBSD Secure Shell server.
         Starting Deferred execution scheduler...
[  OK  ] Started Deferred execution scheduler.
         Starting Internet superserver...
[  OK  ] Started Internet superserver.
         Starting /etc/rc.local Compatibility...
         Starting LSB: Start NTP daemon...
         Starting dnsmasq - A lightweight DHCP and caching DNS server...
         Starting System Logging Service...
         Starting Permit User Sessions...
[  OK  ] Started /etc/rc.local Compatibility.
[  OK  ] Started Permit User Sessions.
         Starting Serial Getty on ttyS0...
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started System Logging Service.
[  OK  ] Started LSB: Start NTP daemon.
[  OK  ] Started dnsmasq - A lightweight DHCP and caching DNS server.
[  OK  ] Reached target Host and Network Name Lookups.
         Starting LSB: exim Mail Transport Agent...

Debian GNU/Linux 8 debwrt ttyS0

debwrt login: