Changes between Initial Version and Version 1 of DebWrtTplinkTLWR1043NDBootlog


Ignore:
Timestamp:
Nov 18, 2012, 7:40:51 PM (8 years ago)
Author:
amain
Comment:

--

Legend:

Unmodified
Added
Removed
Modified
  • DebWrtTplinkTLWR1043NDBootlog

    v1 v1  
     1= DebWrt TP-Link TL-WR1043ND Boot log =
     2
     3{{{
     4U-Boot 1.1.4 (Mar 31 2012 - 10:40:21)
     5
     6AP83 (ar9100) U-boot 0.0.11
     7DRAM: 
     8sri
     932 MB
     10id read 0x100000ff
     11flash size 8MB, sector count = 128
     12Flash:  8 MB
     13Using default environment
     14
     15In:    serial
     16Out:   serial
     17Err:   serial
     18Net:   ag7100_enet_initialize...
     19No valid address in Flash. Using fixed address
     20: cfg1 0xf cfg2 0x7114
     21eth0: 00:03:7f:09:0b:ad
     22eth0 up
     23eth0
     24Autobooting in 1 secondsar7100>
     25ar7100> tftpboot 0x81000000 debwrt-firmware-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin
     26dup 1 speed 1000
     27Using eth0 device
     28TFTP from server 192.168.0.5; our IP address is 192.168.0.2
     29Filename 'debwrt-firmware-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin'.
     30Load address: 0x81000000
     31Loading: T T T T #################################################################
     32         #################################################################
     33         #################################################################
     34         #################################################################
     35         #################################################################
     36         #################################################################
     37         #################################################################
     38         #################################################################
     39         #################################################################
     40         #################################################################
     41         #################################################################
     42         #################################################################
     43         #################################################################
     44         #################################################################
     45         #################################################################
     46         #################################################################
     47         #################################################################
     48         #################################################################
     49         #################################################################
     50         #################################################################
     51         #################################################################
     52         #################################################################
     53         #################################################################
     54         #################################################################
     55         ############################
     56done
     57Bytes transferred = 8126464 (7c0000 hex)
     58ar7100> erase 0xbf020000 +7c0000
     59
     60First 0x2 last 0x7d sector size 0x10000
     61 125
     62Erased 124 sectors
     63ar7100> cp.b 0x81000000 0xbf020000 0x7c0000
     64Copy to Flash... write addr: bf020000
     65done
     66ar7100> bootm 0xbf020000                   
     67## Booting image at bf020000 ...
     68   Uncompressing Kernel Image ... OK
     69
     70Starting kernel ...
     71
     72
     73
     74OpenWrt kernel loader for AR7XXX/AR9XXX
     75Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
     76Looking for OpenWrt image... found at 0xbf022000
     77Decompressing kernel... done!
     78Starting kernel at 80060000...
     79
     80[    0.000000] Linux version 3.3.8 (bitten@slave2) (gcc version 4.6.4 20121001 (prerelease) (Linaro GC2
     81[    0.000000] bootconsole [early0] enabled
     82[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
     83[    0.000000] SoC: Atheros AR9132 rev 2
     84[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
     85[    0.000000] Determined physical RAM map:
     86[    0.000000]  memory: 02000000 @ 00000000 (usable)
     87[    0.000000] Initrd not found or empty - disabling initrd
     88[    0.000000] Zone PFN ranges:
     89[    0.000000]   Normal   0x00000000 -> 0x00002000
     90[    0.000000] Movable zone start PFN for each node
     91[    0.000000] Early memory PFN ranges
     92[    0.000000]     0: 0x00000000 -> 0x00002000
     93[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
     94[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
     95[    0.000000] Kernel command line:  board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 d
     96[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
     97[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
     98[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
     99[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
     100[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
     101[    0.000000] Writing ErrCtl register=00000000
     102[    0.000000] Readback ErrCtl register=00000000
     103[    0.000000] Memory: 28476k/32768k available (2628k kernel code, 4292k reserved, 505k data, 224k ini)
     104[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
     105[    0.000000] NR_IRQS:51
     106[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
     107[    0.080000] pid_max: default: 32768 minimum: 301
     108[    0.080000] Mount-cache hash table entries: 512
     109[    0.090000] NET: Registered protocol family 16
     110[    0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
     111[    0.100000] MIPS: machine is TP-LINK TL-WR1043ND
     112[    0.370000] bio: create slab <bio-0> at 0
     113[    0.370000] SCSI subsystem initialized
     114[    0.380000] usbcore: registered new interface driver usbfs
     115[    0.380000] usbcore: registered new interface driver hub
     116[    0.390000] usbcore: registered new device driver usb
     117[    0.390000] Switching to clocksource MIPS
     118[    0.400000] NET: Registered protocol family 2
     119[    0.400000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
     120[    0.410000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
     121[    0.420000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
     122[    0.420000] TCP: Hash tables configured (established 1024 bind 1024)
     123[    0.430000] TCP reno registered
     124[    0.430000] UDP hash table entries: 256 (order: 0, 4096 bytes)
     125[    0.440000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
     126[    0.440000] NET: Registered protocol family 1
     127[    0.470000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
     128[    0.470000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Ha.
     129[    0.480000] msgmni has been set to 55
     130[    0.490000] io scheduler noop registered
     131[    0.490000] io scheduler deadline registered (default)
     132[    0.500000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
     133[    0.530000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
     134[    0.530000] console [ttyS0] enabled, bootconsole disabled
     135[    0.530000] console [ttyS0] enabled, bootconsole disabled
     136[    0.550000] loop: module loaded
     137[    0.550000] Uniform Multi-Platform E-IDE driver
     138[    0.560000] ide-gd driver 1.18
     139[    0.570000] m25p80 spi0.0: found s25sl064a, expected m25p80
     140[    0.570000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
     141[    0.580000] 5 tp-link partitions found on MTD device spi0.0
     142[    0.580000] Creating 5 MTD partitions on "spi0.0":
     143[    0.590000] 0x000000000000-0x000000020000 : "u-boot"
     144[    0.590000] 0x000000020000-0x000000138c00 : "kernel"
     145[    0.600000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller y
     146[    0.610000] 0x000000138c00-0x0000007f0000 : "rootfs"
     147[    0.620000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller y
     148[    0.630000] mtd: partition "rootfs" set to be root filesystem
     149[    0.640000] mtd: partition "rootfs_data" created automatically, ofs=290000, len=560000
     150[    0.650000] 0x000000290000-0x0000007f0000 : "rootfs_data"
     151[    0.650000] 0x0000007f0000-0x000000800000 : "art"
     152[    0.660000] 0x000000020000-0x0000007f0000 : "firmware"
     153[    0.670000] Realtek RTL8366RB ethernet switch driver version 0.2.3
     154[    0.790000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
     155[    0.790000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
     156[    0.970000] rtl8366rb: probed
     157[    0.980000] eth0: Atheros AG71xx at 0xb9000000, irq 4
     158[    1.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     159[    1.290000] ehci-platform ehci-platform: Generic Platform EHCI Controller
     160[    1.300000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
     161[    1.340000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
     162[    1.360000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
     163[    1.360000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
     164[    1.370000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     165[    1.380000] usb usb1: Product: Generic Platform EHCI Controller
     166[    1.380000] usb usb1: Manufacturer: Linux 3.3.8 ehci_hcd
     167[    1.390000] usb usb1: SerialNumber: ehci-platform
     168[    1.390000] hub 1-0:1.0: USB hub found
     169[    1.400000] hub 1-0:1.0: 1 port detected
     170[    1.400000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
     171[    1.410000] uhci_hcd: USB Universal Host Controller Interface driver
     172[    1.420000] Initializing USB Mass Storage driver...
     173[    1.420000] usbcore: registered new interface driver usb-storage
     174[    1.430000] USB Mass Storage support registered.
     175[    1.430000] TCP cubic registered
     176[    1.430000] NET: Registered protocol family 17
     177[    1.440000] Bridge firewalling registered
     178[    1.440000] 8021q: 802.1Q VLAN Support v1.8
     179[    1.450000] console [netcon0] enabled
     180[    1.450000] netconsole: network logging started
     181[    1.460000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
     182[    1.470000] Freeing unused kernel memory: 224k freed
     183[    1.730000] usb 1-1: new high-speed USB device number 2 using ehci-platform
     184[    1.940000] usb 1-1: New USB device found, idVendor=1058, idProduct=070b
     185[    1.940000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
     186[    1.950000] usb 1-1: Product: My Passport 070B
     187[    1.960000] usb 1-1: Manufacturer: Western Digital
     188[    1.960000] usb 1-1: SerialNumber: 575847304142393434323837
     189[    2.080000] scsi0 : usb-storage 1-1:1.0
     190[    3.080000] scsi 0:0:0:0: Direct-Access     WD       My Passport 070B 1032 PQ: 0 ANSI: 4
     191[    3.170000] sd 0:0:0:0: [sda] 623769600 512-byte logical blocks: (319 GB/297 GiB)
     192[    3.180000] scsi 0:0:0:1: CD-ROM            WD       Virtual CD 070B  1032 PQ: 0 ANSI: 4
     193[    3.320000] sd 0:0:0:0: [sda] Write Protect is off
     194[    3.320000] scsi 0:0:0:2: Enclosure         WD       SES Device       1032 PQ: 0 ANSI: 4
     195[    3.330000] sd 0:0:0:0: [sda] No Caching mode page present
     196[    3.340000] sd 0:0:0:0: [sda] Assuming drive cache: write through
     197[    3.350000] sd 0:0:0:0: [sda] No Caching mode page present
     198[    3.360000] sd 0:0:0:0: [sda] Assuming drive cache: write through
     199[ ---------- ] DebWrt boot
     200[ ---------- ] Waiting for device with LABEL=DEBWRT_ROOT...[    3.740000]  sda: sda1 sda2
     201[    3.750000] sd 0:0:0:0: [sda] No Caching mode page present
     202[    3.750000] sd 0:0:0:0: [sda] Assuming drive cache: write through
     203[    3.760000] sd 0:0:0:0: [sda] Attached SCSI disk
     204found. Booting from /dev/sda1.
     205[    5.140000] kjournald starting.  Commit interval 5 seconds
     206[    5.150000] EXT3-fs (sda1): using internal journal
     207[    5.150000] EXT3-fs (sda1): mounted filesystem with writeback data mode
     208[    5.350000] Algorithmics/MIPS FPU Emulator v1.5
     209umount: /mnt: device is busy.
     210        (In some cases useful info about processes that use
     211         the device is found by lsof(8) or fuser(1))
     212INIT: version 2.88 booting
     213Using makefile-style concurrent boot in runlevel S.
     214.udev/ already exists on the static /dev! ... (warning).
     215Starting the hotplug events dispatcher: udevd.
     216Synthesizing the initial hotplug events...done.
     217Waiting for /dev to be fully populated...[    7.510000] Compat-drivers backport release: compat-driver3
     218[    7.520000] Backport based on wireless-testing.git master-2012-09-07
     219[    7.530000] compat.git: wireless-testing.git
     220[    7.830000] cfg80211: Calling CRDA to update world regulatory domain
     221[    7.840000] cfg80211: World regulatory domain updated:
     222[    7.840000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
     223[    7.850000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     224[    7.860000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
     225[    7.870000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
     226[    7.870000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     227[    7.880000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     228[    8.480000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
     229[    8.500000] cfg80211: Calling CRDA for country: US
     230[    8.500000] cfg80211: Regulatory domain changed to country: US
     231[    8.510000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
     232[    8.510000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
     233[    8.520000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
     234[    8.530000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     235[    8.540000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     236[    8.550000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     237[    8.550000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
     238done.
     239Setting parameters of disc: (none).
     240Activating swap...[    9.460000] Adding 530140k swap on /dev/sda2.  Priority:-1 extents:1 across:53014
     241done.
     242Cleaning up ifupdown....
     243Setting up networking....
     244Loading kernel modules...done.
     245Activating lvm and md swap...done.
     246Checking file systems...fsck from util-linux-ng 2.17.2
     247done.
     248Mounting local filesystems...done.
     249Activating swapfile swap...done.
     250Cleaning up temporary files....
     251Configuring network interfaces...Loading firewall - starting...[   11.630000] ip_tables: (C) 2000-2006m
     252[   11.700000] nf_conntrack version 0.5.0 (448 buckets, 1792 max)
     253done.
     254[   11.970000] eth0: link up (1000Mbps/Full duplex)
     255Internet Systems Consortium DHCP Client 4.1.1-P1
     256Copyright 2004-2010 Internet Systems Consortium.
     257All rights reserved.
     258For info, please visit https://www.isc.org/software/dhcp/
     259
     260Listening on LPF/wan/f4:ec:38:dd:9a:fe
     261Sending on   LPF/wan/f4:ec:38:dd:9a:fe
     262Sending on   Socket/fallback
     263[   13.950000] device lan entered promiscuous mode
     264[   13.960000] device eth0 entered promiscuous mode
     265[   14.010000] br-lan: port 1(lan) entered forwarding state
     266[   14.010000] br-lan: port 1(lan) entered forwarding state
     267Starting advanced IEEE 802.11 management: hostapd[   14.420000] device wifi entered promiscuous mode
     268[   14.780000] br-lan: port 2(wifi) entered forwarding state
     269[   14.790000] br-lan: port 2(wifi) entered forwarding state
     270.
     271done.
     272Cleaning up temporary files....
     273Setting kernel variables ...done.
     274INIT: Entering runlevel: 2
     275Using makefile-style concurrent boot in runlevel 2.
     276Starting enhanced syslogd: rsyslogd.
     277Starting periodic command scheduler: cron.
     278Starting NTP server: ntpd.
     279Starting internet superserver: inetd.
     280Starting Shell In A Box Daemon: shellinabox.
     281Starting OpenBSD Secure Shell server: sshd[   18.500000] sshd (1335): /proc/1335/oom_adj is deprecated.
     282.
     283
     284Debian GNU/Linux 6.0 debwrt ttyS0
     285
     286debwrt login: [   29.040000] br-lan: port 1(lan) entered forwarding state
     287[   29.840000] br-lan: port 2(wifi) entered forwarding state                   
     288
     289}}}